Maytag MVWP575GW – Common Problems

People say technology is everyone’s friend, but this becomes hard to believe when technological devices start malfunctioning.

Of course, it’s not because these devices are not good. Instead, these devices develop some difficulties now and then.

The Maytag MVWP575GW is one such device.

This washing machine is suitable for heavy loads and has beautiful features like an agitator and various temperature and cloth washing options.

However, there are still some common challenges associated with this product.

Common Problems Associated With The Maytag MVWP575GW

Loud Noises

Every technological device has the usual sounds it makes when working. It also applies to washers.

However, these sounds could become excessive when the washer starts to develop some technological issues.

You might wonder, “How bad could those noises be?” They could become so bad that they become a nuisance in your home.

Every time you put clothes in your washer, you feel on edge because you must keep checking on the washer.

The entire point of getting a washer in the first place was to wash your clothes without having to supervise anything.

How well can you achieve this if you have to keep checking on your washer because of some loud noises?

Besides, the longer you leave your washer in that condition, the more unsafe it becomes for use.

If it starts malfunctioning, you can hear three types of noises from your washer: grinding, humming, and squealing.

Grinding noises occur when a part of your washer is worn out. Humming noises happen when something gets stuck in some areas of your washer.

Finally, squealing noises signify that some parts of your washer have been stretched beyond their limit.

Loud Noises: Causes

1. The machine might be overloaded.
2. The washer isn’t leveled against the floor.
3. One of the spokes in your drum pulley is damaged
4. The belt is making some squealy noises

Solution

1. Check your product manual for loading instructions and follow them accordingly.
2. Ensure all four feet of the washer are leveled by tightening the nuts against the washer cabinet.
3. Replace the pulley.
4. Add some Marseille soap to the belt, but you might have to replace the belt entirely if this doesn’t work.

Poor Draining System

Before deciding to get a washer, there are certain things you probably had in mind.

The major one is that you want to make cloth washing easier and faster for you.

But, of course, this is only possible if the washer makes your clothes clean and dry.

However, one of those desires becomes defeated when the washer develops problems with its draining system.

So, instead of getting clean and dry clothes, you’re getting clean clothes drenched in water.

It means you would still have to do further work by spreading your clothes so they can dry completely.

In such instances, the washer becomes useless because it doesn’t fulfill its purpose. The idea is to skip the stress and time involved in drying clothes.

But with a poor draining system, that’s impossible. Another downside is that the water can overflow and damage your floors.

It can sometimes be so severe that it might lead to flooding.

Poor Draining System: Causes

1. A foreign object stuck in the drain pump or a damaged drain pump impeller
2. The door lock assembly is defective when the door isn’t locked correctly or is faulty
3. Clogs in the washer’s coin trap or drain hose

Solution

1. Remove the foreign objects causing the blockage or replace the drain pump entirely.
2. Replace the door lock motor and switch assembly by unthreading the screws of the previous one to fix another.
3. Clean the coin trap by removing it from its panel and rinsing it under your sink.

Faulty Washer Doors/Lids

Almost every product or thing has a cover, door, or lid to keep it intact.

Skincare and hair products have caps and covers to prevent air from damaging the products. Houses are built with doors for safety reasons.

Similarly, the Maytag MVWP575GW was made with a lid to ensure the safety of its users.

Indeed, you might still use your washer without the lid, but this isn’t safe. It could cause injury to people nearby.

Sometimes, the washer’s doors or lid get stuck. It makes the washer even more unsafe for use.

A Maytag washer lid can become faulty due to mechanical and electrical reasons.

For example, mechanical difficulties occur when the door lock is defective, and the washer door doesn’t close properly.

On the other hand, electrical defects arise when one of the door lock switches lacks continuity.

Faulty Washer Doors/Lids: Causes

1. A faulty door could occur due to mechanical and electrical reasons
2. A faulty door latch
3. A defect in the main control board

Solution

1. Use a multimeter to test the washer’s door lock switches for continuity. If any of the switches are faulty, you must replace them.
2. Replace the door latch if it’s damaged.
3. Don’t be too quick to replace the main control board. First, check all the constituents of the lock mechanism. If you’re unable to find any defects, then you can go on to replace the main control board.

Agitator Malfunction

For clothes to be clean, there needs to be a certain amount of pressure or movement applied to them.

For example, when washing clothes manually, you use pressure by rubbing the clothes between both hands.

But of course, that gets tiring quickly, so you decided to get the Maytag MVWP575GW.

In this device, many parts work together to provide clean and dry clothes. At the center of all these parts is the agitator.

Unlike its appearance, the agitator isn’t the primary device that causes your washer to spin.

Instead, it is that device that acts as the hands of the washer to ensure your clothes are clean.

It is also part of the washer that distributes the soap and cleans off the dirt from your clothes.

So, once your agitator malfunctions, you’d realize that your clothes went through a wash process but still came out unclean.

In some cases, the agitator might still be working but not as effective as it used to.

Agitator Malfunction: Causes

1. A damaged agitator assembly is caused by a weak agitator shaft or an obstruction caused by a wire or fan blade.
2. When the drive belt loses its elasticity or becomes broken
3. Bad transmission
4. An issue with the motor coupling
5. A worn-out or damaged drive block

Solution

1. First, check the agitator assembly for signs of wear or dents. You might have to call a repair specialist if the agitator’s condition is beyond a quick fix.
2. If you’re having issues with the transmission, it might be time to get a new washer, as the cost of fixing this is almost the same as a new washer.
3. Check the condition of the motor coupling and replace it if faulty.
4. Check the drive block to ensure it is adequately intact on the drive shaft. If it is and your washer still isn’t agitating, it might be time to replace the drive block.

Maytag MVWP575GW Common Problems – Conclusion

Despite all its good qualities, the Maytag MVWP575GW still tends to malfunction in different areas. However, you can solve these issues with an easy fix.

The primary key is knowing the causes behind the problem you’re facing. Then, you can decide on the best repair methods to apply.